STM32F769I Discovery Kit Setup Instructions
This topic helps you setup the development environment for STM's STM32F769I discovery kit.
- STM32F769NIH6 MCU (ARM® Cortex®-M7)
- 4” capacitive touch LCD display (800x480)
- 512+16+4 Kbytes of RAM
- 128-Mbit SDRAM
- 2 MB Flash memory
- 512-Mbit Quad-SPI NOR Flash memory
More information fromSTM32F769I Discovery Website
- Ensure that the common STM prerequisites are met
- Install STM32CubeF7 SDK 1.16.0 or newer (provided by the Qt online installer)
- Launch Qt Creator and select Tools > Options > Devices > MCU.
- Select the one of the targets from the drop-down list for Target supported by the Qt for MCUs SDK:
- Qt for MCUs 1.5 - STM32F769I-DISCOVERY-BAREMETAL 32bpp
- Qt for MCUs 1.5 - STM32F769I-DISCOVERY-FREERTOS 32bpp
- Provide the STM32CubeProgrammer install path if it is not installed in the default location.
- In the Requirements section, ensure that the platform-specific requirements are met.
- Select Create Kit to create a kit for the selected target. if a kit already exists, remove it first using Remove Kit.
Note: If you don't see the option to create a kit, check your settings in the Requirements section.
- Click Apply.
To get started from the command line, ensure that the following these instructions:
Qul_DIRto the Qt for MCUs SDK install path.
<QT_INSTALL_PATH>is the Qt install directory,
<VERSION>is the directory containing the Qt Quick Ultralite version you are using, for example
ARMGCC_DIRto the ARM Toolchain install path.
- Add the CMake and Ninja tools to your system
PATH. If you installed these tools using the Qt online installer, they are installed under
- Add STM32CubeProg install directory to
System PATHif it is not installed in the default location.
ST-LINK_gdbserver.exedirectory to your
<STM32_CUBE_IDE_INSTALL_PATH>is the Cube IDE install path.
Note: STM32CubeIDE is optional and required only for on-chip debugging purposes.
- Create the
STM32Cube_FW_F7_SDK_PATHenvironment variable and set it to the following path:
<QT_INSTALL_PATH>is the Qt install directory.
Qt Creator provides a build configuration with the kits that you created earlier for the targets. If you are using a command line setup, configure using the following CMake variables. For more information, see the CMake Manual.
The platform to build must be set to
stm32f769i-discovery-baremetalfor this board.
This platform supports armgcc compiler.
The supported color depth by this platform is 32-bit.
Note: If this variable is not set, default color depth is used while configuring for the platform.
By default, the asset data for application is copied to SDRAM on application startup. In order to keep resources in external flash, and not load it to RAM on startup, use the QUL_COPY_TO_RAM CMake option with the value
Neverwhen adding assets to the application with qul_add_resource.
The package for
STM32f769I-DISCOVERY board comes with a prebuilt thermo demo binary. As Qt Quick Ultralite supports both bare metal and FreeRTOS on this board, there are different binaries for both under the
demos_images directory. Also
Thermo demo has two variants, one with metric units and another with imperial units.
See the flashing instructions for the ST boards section, for more information on flashing the device. For this board, select
MX25L512G_STM32F769I-DISCO as the external loader.
Qt for MCUs provides the source code of several demos and examples. You can modify, build, and flash custom binaries onto the target device.
Source code for supported demos and examples is organized in the following directory structure:
Note: build targets for this example are styling_custom and styling_default
Note: build targets for this example are translation_all and translation_lv
Note: Demos or examples that are highlighted in bold are the only ones supported on this board.
Open the CMake project file for the example you want to build and configure it with the kit you created earlier. Once the project is configured, select Run or press Ctrl+r on your keyboard to build and flash the binary to the target.
The following example builds the
thermo demo for this board:
cd %Qul_DIR%\demos\thermo mkdir build cd build cmake .. -G "Ninja" -DCMAKE_BUILD_TYPE=Debug -DCMAKE_TOOLCHAIN_FILE=%Qul_DIR%\lib\cmake\Qul\toolchain\armgcc.cmake -DQUL_PLATFORM=STM32F769I-DISCOVERY-baremetal cmake --build .
Once you have successfully built the
thermo demo, you can flash it from command line:
cmake --build . --target flash_thermo_big
The same procedure applies to any other application.
To build demos or examples for FreeRTOS, add the
STM32F7_FREERTOS_DIR environment variable and set its value to the FreeRTOS source directory from STM32CubeF7. For example:
The build steps are same as for bare metal, just the platform name is different:
cmake .. -G "Ninja" -DCMAKE_BUILD_TYPE=Release -DCMAKE_TOOLCHAIN_FILE=%Qul_DIR%\lib\cmake\Qul\toolchain\armgcc.cmake -DQUL_PLATFORM=STM32F769I-DISCOVERY-freertos
Note: If you already built the example earlier with default configuration, you must clean the build directory or use another build directory (
build_freertos for example).
For more information about FreeRTOS integration, refer to Using Qt Quick Ultralite with FreeRTOS.
By default, the output of
printf calls are redirected to STLink virtual COM Port, which is exposed on the host machine via USB. Serial configuration is following:
Baud rate: 115200 Data bits: 8 Stop bits: 1 Parity: None Flow control: None
- Open terminal window and run the following command:
ST-LINK_gdbserver.exe -cp "<STM32_CUBE_PROG_INSTALL_PATH>\bin"
<STM32_CUBE_PROG_INSTALL_PATH>is the directory where you've installed the Cube Programmer tool.
GDB Server is now listening for TCP connections on the default port,
Note: Actual TCP port used by
ST-LINK_gdbserveris printed out on gdbserver's console.
arm-none-eabi-gdbin a separate console
- Connect to the target via the gdbserver in the
(gdb) target remote 127.0.0.1:61234
ST-LINK_gdbserver requires up-to-date ST-LINK firmware to be installed. If you see the following error:
Error in initializing ST-LINK device. Reason: ST-LINK firmware upgrade required.
you must upgrade the firmware to the latest version using the STM32CubeProgrammer tool.
If the problem persists after upgrade, retry with
ST-LINK Upgrade tool from the ST webpage ( Download ).
Available under certain Qt licenses.
Find out more.