STM32H750B Discovery Kit Setup Instructions
This topic helps your setup the development environment for STM's STM32H750B discovery kit.
- Dual-Core ARM® Cortex®-M7 and -M4
- 4.3” RGB Touch Display
- 128-Mbit SDRAM
- 1 Mbit NOR Flash
- 4-Gbyte on-board eMMC
- Ensure that the common STM prerequisites are met
- Install STM32CubeH7 SDK 1.5.0 (provided by the Qt online installer)
- Flash the bootloader image onto the device. See Bootloader Flashing Instructions for ST boards
- Launch Qt Creator and select Tools > Options > Devices > MCU.
- Select the Qt for MCUs 1.5 - STM32H750B-DISCOVERY-BAREMETAL 32bpp from the drop-down list for Target supported by the Qt for MCUs SDK.
- Provide the STM32CubeProgrammer install path if it is not installed in the default location.
- In the Requirements section, ensure that the platform-specific requirements are met.
- Select Create Kit to create a kit for the selected target. if a kit already exists, remove it first using Remove Kit.
Note: If you don't see the option to create a kit, check your settings in the Requirements section.
- Click Apply.
To get started from the command line, ensure that the following these instructions:
Qul_DIRto the Qt for MCUs SDK install path.
<QT_INSTALL_PATH>is the Qt install directory,
<VERSION>is the directory containing the Qt Quick Ultralite version you are using, for example
ARMGCC_DIRto the ARM Toolchain install path.
- Add the CMake and Ninja tools to your system
PATH. If you installed these tools using the Qt online installer, they are installed under
- Add STM32CubeProg install directory to
System PATHif it is not installed in the default location.
ST-LINK_gdbserver.exedirectory to your
<STM32_CUBE_IDE_INSTALL_PATH>is the Cube IDE install path.
Note: STM32CubeIDE is optional and required only for on-chip debugging purposes.
- Create the
STM32Cube_FW_H7_SDK_PATHenvironment variable and set its value to the following:
where, <QT_INSTALL_PATH> is the Qt install directory.
Qt Creator provides a build configuration with the kit that you created earlier for the Qt for MCUs 1.5 - STM32H750B-DISCOVERY-BAREMETAL 32bpp target. If you are using a command line setup, configure using the following CMake variables. For more information, see the CMake Manual.
The platform to build must be set to
stm32h750b-discovery-baremetalfor this board.
This platform supports armgcc compiler.
The supported color depth by this platform is 32-bit.
Note: If this variable is not set, default color depth is used while configuring for the platform.
By default, the asset data for application is copied to SDRAM on application startup. In order to keep resources in external flash, and not load it to RAM on startup, use the QUL_COPY_TO_RAM CMake option with the value
Neverwhen adding assets to the application with qul_add_resource.
The package for
STM32H750B board comes with a prebuilt thermo demo binary. You can find it in the
See Flashing Instructions for ST boards section on how to flash the device.'
Qt for MCUs provides the source code of several demos and examples. You can modify, build, and flash custom binaries onto the target device.
Source code for supported demos and examples is organized in the following directory structure:
Note: Demos or examples that are highlighted in bold are the only ones supported on this board.
Open the CMake project file for the example you want to build and configure it with the kit you created earlier. Once the project is configured, select Run or press Ctrl+r on your keyboard to build and flash the binary to the target.
The following example builds the
watch demo for this board:
cd %Qul_DIR%\demos\watch mkdir build cd build cmake .. -G "Ninja" -DCMAKE_BUILD_TYPE=Debug -DCMAKE_TOOLCHAIN_FILE=%Qul_DIR%\lib\cmake\Qul\toolchain\armgcc.cmake -DQUL_PLATFORM=stm32h750b-discovery-baremetal cmake --build .
Once you have successfully built the
watch demo, you can flash it from command line:
cmake --build . --target flash_watch
The same procedure applies to any other application.
By default, the output of
printf calls are redirected to a virtual serial port, which is exposed on the host machine via USB.
- Open terminal window and run the following command:
ST-LINK_gdbserver.exe -cp "<STM32_CUBE_PROG_INSTALL_PATH>\bin"
<STM32_CUBE_PROG_INSTALL_PATH>is the directory where you've installed the Cube Programmer tool.
GDB Server is now listening for TCP connections on the default port,
Note: Actual TCP port used by
ST-LINK_gdbserveris printed out on gdbserver's console.
arm-none-eabi-gdbin a separate console
- Connect to the target via the gdbserver in the
(gdb) target remote 127.0.0.1:61234
ST-LINK_gdbserver requires up-to-date ST-LINK firmware to be installed. If you see the following error:
Error in initializing ST-LINK device. Reason: ST-LINK firmware upgrade required.
you must upgrade the firmware to the latest version using the STM32CubeProgrammer tool.
If the problem persists after upgrade, retry with
ST-LINK Upgrade tool from the ST webpage ( Download ).
- The newer SDK version 1.6.0 is not supported yet.
Available under certain Qt licenses.
Find out more.