|qmake:||QT += network|
This class was introduced in Qt 4.8.
|QHttpPart(const QHttpPart &other)|
|QHttpPart &||operator=(const QHttpPart &other)|
|void||setBody(const QByteArray &body)|
|void||setHeader(QNetworkRequest::KnownHeaders header, const QVariant &value)|
|void||setRawHeader(const QByteArray &headerName, const QByteArray &headerValue)|
|bool||operator!=(const QHttpPart &other) const|
|bool||operator==(const QHttpPart &other) const|
The QHttpPart class holds a body part to be used inside a HTTP multipart MIME message (which is represented by the QHttpMultiPart class). A QHttpPart consists of a header block and a data block, which are separated by each other by two consecutive new lines. An example for one part would be:
Content-Type: text/plain Content-Disposition: form-data; name="text" here goes the body
For reading small pieces of data, use setBody(); for larger data blocks like e.g. images, use setBodyDevice(). The latter method saves memory by not copying the data internally, but reading directly from the device. This means that the device must be opened and readable at the moment when the multipart message containing the body part is sent on the network via QNetworkAccessManager::post().
To construct a QHttpPart with a small body, consider the following snippet (this produces the data shown in the example above):
QHttpPart textPart; textPart.setHeader(QNetworkRequest::ContentTypeHeader, QVariant("text/plain")); textPart.setHeader(QNetworkRequest::ContentDispositionHeader, QVariant("form-data; name=\"text\"")); textPart.setBody("here goes the body");
To construct a QHttpPart reading from a device (e.g. a file), the following can be applied:
QHttpPart imagePart; imagePart.setHeader(QNetworkRequest::ContentTypeHeader, QVariant("image/jpeg")); imagePart.setHeader(QNetworkRequest::ContentDispositionHeader, QVariant("form-data; name=\"image\"")); imagePart.setRawHeader("Content-ID", "firstname.lastname@example.org"); // add any headers you like via setRawHeader() QFile *file = new QFile("image.jpg"); file->open(QIODevice::ReadOnly); imagePart.setBodyDevice(file);
Be aware that QHttpPart does not take ownership of the device when set, so it is the developer's responsibility to destroy it when it is not needed anymore. A good idea might be to set the multipart message as parent object for the device, as documented at the documentation for QHttpMultiPart.
Member Function Documentation
QHttpPart::QHttpPart(const QHttpPart &other)
Creates a copy of other.
Constructs an empty QHttpPart object.
Creates a copy of other.
Destroys this QHttpPart.
void QHttpPart::setBody(const QByteArray &body)
Sets the body of this MIME part to body. The body set with this method will be used unless the device is set via setBodyDevice(). For a large amount of data (e.g. an image), use setBodyDevice(), which will not copy the data internally.
See also setBodyDevice().
void QHttpPart::setBodyDevice(QIODevice *device)
Sets the device to read the content from to device. For large amounts of data this method should be preferred over setBody(), because the content is not copied when using this method, but read directly from the device. device must be open and readable. QHttpPart does not take ownership of device, i.e. the device must be closed and destroyed if necessary. if device is sequential (e.g. sockets, but not files), QNetworkAccessManager::post() should be called after device has emitted finished(). For unsetting the device and using data set via setBody(), use "setBodyDevice(0)".
void QHttpPart::setHeader(QNetworkRequest::KnownHeaders header, const QVariant &value)
Sets the value of the known header header to be value, overriding any previously set headers.
void QHttpPart::setRawHeader(const QByteArray &headerName, const QByteArray &headerValue)
Sets the header headerName to be of value headerValue. If headerName corresponds to a known header (see QNetworkRequest::KnownHeaders), the raw format will be parsed and the corresponding "cooked" header will be set as well.
Note: Setting the same header twice overrides the previous setting. To accomplish the behaviour of multiple HTTP headers of the same name, you should concatenate the two values, separating them with a comma (",") and set one single raw header.
void QHttpPart::swap(QHttpPart &other)
Swaps this HTTP part with other. This function is very fast and never fails.
This function was introduced in Qt 5.0.
bool QHttpPart::operator!=(const QHttpPart &other) const
true if this object is not the same as other.
See also operator==().
bool QHttpPart::operator==(const QHttpPart &other) const
true if this object is the same as other (i.e., if they have the same headers and body).
See also operator!=().
© 2019 The Qt Company Ltd. Documentation contributions included herein are the copyrights of their respective owners. The documentation provided herein is licensed under the terms of the GNU Free Documentation License version 1.3 as published by the Free Software Foundation. Qt and respective logos are trademarks of The Qt Company Ltd. in Finland and/or other countries worldwide. All other trademarks are property of their respective owners.