Using Lights

Light components are the primary source of lighting in a Qt Design Studio scene. As a secondary light source, you can use image-based lighting.

By default, all imported scenes are created with one directional light. You can use the following Qt Quick 3D components to add lights:

Note: Each additional light negatively effects the rendering performance of your scene. Keep scenes as simple as possible and use lights sparingly. Use a Scene Environment component to apply image-based lighting that can produce soft and subtle lighting.

You can edit light properties in the Properties view. The Scope property specifies which node, with it's children, is illuminated by a light.

Set the Color property to specify the color applied to models illuminated by a light. Set the Ambient color property to specify the ambient color applied to materials before being illuminated by the light.

You can animate light properties in the Timeline view.

Directional Light

A directional light emits light in one direction from a unidentifiable source located infinitely far away. This is similar to sunlight.

"Models lit by a dirctional light"

If the Casts shadow property is enabled, shadows are positioned parallel to the light direction. A directional light has infinite range and does not diminish.

Moving a directional light does not have any effect. The light will always be emitted in the direction of the light's z axis. Rotating the light along its x or y axis will change the direction in which the light is emitted.

Scaling a directional light will only have an effect in the following cases:

  • If the z scale is set to a negative number, the light will be emitted in the opposite direction.
  • If the scale of any axis is set to 0, the light will be emitted along the world's z axis. Rotating the light has no effect.

Point Light

A point light can be described as a sphere, emitting light with equal strength in all directions from the center of the light. This is similar to the way a light bulb emits light.

"Models lit by a point light"

Lighting is applied outwards from the center of a point light, becoming increasingly dim away from the center. Moving a point light changes the position from where the light is emitted. Rotating or scaling a point light does not have any effect.

To specify an overall multiplier for a point light's effects, set the Brightness property.

To control the fade-off and range of a point light, set the Constant fade, Linear fade, and Quadratic fade properties. Constant fade is the constant factor of the attenuation term of the light. Attenuation refers to the reduction in the intensity of light as it travels through a medium due to absorption or scattering of photons.

Turn up the linear fade value to increase the rate at which the lighting effect dims the light in proportion to the distance to the light. The value 0.0 means that the light doesn't have linear fade.

Turn up the quadratic fade to increase the rate at which the lighting effect dims on surfaces that are far away from the light. The value 1.0 means that the point light fade exactly follows the inverse square law. For example, when the distance to an object doubles, the light intensity decreases to one fourth.

Aside from fade, a point light has the same properties as a directional light.

Spot Light

A spot light emits light towards one direction in a cone shape. The light intensity diminishes when approaching the value of the Cone angle property. The angle at which the light intensity starts to diminish is defined by the Inner cone angle property. Both angles are defined in degrees.

Inside the inner cone angle, the spot light behaves similarly to the point light. There the light intensity diminishes according to inverse-square-law. However, the fade-off (and range) can be controlled with the Constant fade, Linear fade, and Quadratic fade properties.

Area Light

An area light is similar to the directional light. However, instead of emitting an equally bright light across the whole scene, the area light emits directional light from a rectangle shaped object. You can set the Width and Height properties to determine the size of the area light.

Aside from the size, an area light has the same properties as a directional light.

The image below shows an example on how to light an object with different colors using two different area lights.

You can rotate, scale, and move area lights.


To simulate shadows using this light, enable the Cast shadows check box. Cast shadows work best with area or point lights.

To specify the darkness of the shadows, set the Shadow factor property. The value 0 means no shadows are cast.

To specify the amount of blur applied to the shadows, set the Shadow filter property.

Tweak the Shadow bias property value by small amounts if you see objects casting shadows on themselves.

To specify the quality of the shadow map created for shadow rendering, set the Shadow map quality property. Lower quality uses less resources, but produces lower quality shadows, while higher quality uses more resources to produce better quality shadows.

To specify the maximum distance for the shadow map, set the Shadow map far property value. Using smaller values may improve the precision and effects of the map.

© 2020 The Qt Company Ltd. Documentation contributions included herein are the copyrights of their respective owners. The documentation provided herein is licensed under the terms of the GNU Free Documentation License version 1.3 as published by the Free Software Foundation. Qt and respective logos are trademarks of The Qt Company Ltd in Finland and/or other countries worldwide. All other trademarks are property of their respective owners.